FLOWDECKV2's setup

Discussions and questions about the Crazyflie Nano Quadcopter
Post Reply
RyanMco
Member
Posts: 32
Joined: Tue Apr 09, 2019 6:15 am

FLOWDECKV2's setup

Post by RyanMco » Wed Apr 17, 2019 11:25 am

Hi guys, I have a real problem with flowdekv2, I succeeded to attach it to my drone, but it sounds it doesn't work, what I have did is:
I was having crazyflie working 100% and after I bought my flowdeckV2 I just attached it to my crazyflie's hardware and sounds it doesn't work(flowdeck isn't responding) .. what should I do ? maybe must I download any software/firmware to interact with my flowdeckV2? in a nutshell, what should I do after connecting physically flowdeckv2 to my crazyflie? thanks alot!!

tobias
Bitcraze
Posts: 1867
Joined: Mon Jan 28, 2013 7:17 pm
Location: Sweden

Re: FLOWDECKV2's setup

Post by tobias » Thu Apr 18, 2019 7:50 am

Can you post your console output, similar to what is done in this thread. Did you mount the flow deck the right way?

RyanMco
Member
Posts: 32
Joined: Tue Apr 09, 2019 6:15 am

Re: FLOWDECKV2's setup

Post by RyanMco » Thu Apr 18, 2019 7:56 pm

it shows me like:
SYS: ----------------------------
SYS: Crazyflie 2.0 is up and running!
SYS: Build 0:a1d5aac6f3e6 (2019.02) MODIFIED
SYS: I am 0x203535523748500700480036 and I have 1024KB of flash!
CFGBLK: v1, verification [OK]
DECK_DRIVERS: Found 16 drivers
DECK_INFO: Found 1 deck memory.
DECK_CORE: 1 deck enumerated
ZR2: Z-down sensor [OK]
PMW: Motion chip id: 0x49:0xB6
MPU9250 I2C connection [OK].
AK8963 I2C connection [OK].
LPS25H I2C connection [OK].
ESTIMATOR: Using estimator 2
CONTROLLER: Using controller 1
EEPROM: I2C connection [OK].
MPU6500: Self test gyro X [FAIL]. low: -14.0, high: 14.0, measured: -30.78
MPU6500: Self test gyro Y [FAIL]. low: -14.0, high: 14.0, measured: -34.99
MPU6500: Self test gyro Y [FAIL]. low: -14.0, high: 14.0, measured: 23.38
MPU6500: Self test gyro Y [FAIL]. low: -14.0, high: 14.0, measured: 22.23
MPU6500: Self test acc X [FAIL]. low: -14.0, high: 14.0, measured: -18.89
MPU6500: Self test gyro Y [FAIL]. low: -14.0, high: 14.0, measured: -25.68
MPU6500: Self test gyro X [FAIL]. low: -14.0, high: 14.0, measured: -18.49
MPU6500: Self test gyro X [FAIL]. low: -14.0, high: 14.0, measured: -34.62
MPU6500: Self test gyro Z [FAIL]. low: -14.0, high: 14.0, measured: 15.38
AK8963: Self test [OK].
DECK_CORE: Deck 0 test [OK].
SYS: Free heap: 11136 bytes
Client uses old logging API!
Client uses old param API!

Client uses old param API!

arnaud
Bitcraze
Posts: 1999
Joined: Tue Feb 06, 2007 12:36 pm

Re: FLOWDECKV2's setup

Post by arnaud » Tue Apr 30, 2019 6:32 am

The flow is enabled in this log and seeing your other posts the flow deck seems to work not so I assume the problem is solved?

Post Reply