FLOWDECK2

Discussions about quadcopters/multi-rotors
Post Reply
RyanMco
Beginner
Posts: 12
Joined: Tue Apr 09, 2019 6:15 am

FLOWDECK2

Post by RyanMco » Tue Apr 09, 2019 6:17 am

Hi guys, what's up?
I'm new on the world of nano crazyflie(fpv) and I'm stuck on how can I connect my FLOWDECK2 onto my crazyflie?
I've the device "flowdeck2" but how can I connect it onto my crazyflie and what I do for configure it on my firmware ?!


thanks alot

RyanMco
Beginner
Posts: 12
Joined: Tue Apr 09, 2019 6:15 am

Re: FLOWDECK2

Post by RyanMco » Tue Apr 09, 2019 6:18 am

If there's any link illustrate step by step how can I connect it, it would be much appreciated .

coreysnipes
Beginner
Posts: 14
Joined: Mon Jan 21, 2019 3:09 am
Location: Cleveland, OH, USA
Contact:

Re: FLOWDECK2

Post by coreysnipes » Wed Apr 10, 2019 2:07 am


RyanMco
Beginner
Posts: 12
Joined: Tue Apr 09, 2019 6:15 am

Re: FLOWDECK2

Post by RyanMco » Tue Apr 16, 2019 6:03 pm

coreysnipes wrote:
Wed Apr 10, 2019 2:07 am
These two should get you going.

first: https://www.bitcraze.io/getting-started ... ion-decks/
and then: https://www.bitcraze.io/getting-started-with-flow-deck/
but there's no infromation about how do I wire my flowdeckV2 hardware (not in aspect of software) on my crazyflie !!
there's no schematic of how do I wire from flowdeckV2 to my drone ..

coreysnipes
Beginner
Posts: 14
Joined: Mon Jan 21, 2019 3:09 am
Location: Cleveland, OH, USA
Contact:

Re: FLOWDECK2

Post by coreysnipes » Wed Apr 17, 2019 12:08 am

Hm, maybe I'm missing something. You don't need to wire or solder anything. You should have some of these deck connectors (a short pair, and a long pair) which attach to the bottom of the CF. https://store.bitcraze.io/collections/s ... -connector

Then you press the flow deck onto those, and it makes all the necessary electrical connections. Make sure you have the correct side facing the CF, and it is pointing the right way.

coreysnipes
Beginner
Posts: 14
Joined: Mon Jan 21, 2019 3:09 am
Location: Cleveland, OH, USA
Contact:

Re: FLOWDECK2

Post by coreysnipes » Wed Apr 17, 2019 12:09 am

This has a quick display of attaching the flow deck, at the beginning. https://www.youtube.com/watch?v=bGvt6Nwja3E

RyanMco
Beginner
Posts: 12
Joined: Tue Apr 09, 2019 6:15 am

Re: FLOWDECK2

Post by RyanMco » Wed Apr 17, 2019 10:59 am

coreysnipes wrote:
Wed Apr 17, 2019 12:08 am
Hm, maybe I'm missing something. You don't need to wire or solder anything. You should have some of these deck connectors (a short pair, and a long pair) which attach to the bottom of the CF. https://store.bitcraze.io/collections/s ... -connector

Then you press the flow deck onto those, and it makes all the necessary electrical connections. Make sure you have the correct side facing the CF, and it is pointing the right way.
what do you mean with "pointing on the right way" ?!

RyanMco
Beginner
Posts: 12
Joined: Tue Apr 09, 2019 6:15 am

Re: FLOWDECK2

Post by RyanMco » Wed Apr 17, 2019 11:19 am

I have bought these deck connectors yesterday and I I attached my flowdeckv2 on it, so what do I do write now? how do I know if it's work or not? which steps of firmware should I follow?! is there any specific software should I use with my flowdeckv2?! thanks!!

Post Reply