[SOLVED]Hurrah! First fix with Ublox

Firmware/software/electronics/mechanics
Post Reply
Mitteau
Expert
Posts: 248
Joined: Fri Jan 29, 2016 6:00 am

[SOLVED]Hurrah! First fix with Ublox

Post by Mitteau »

Hi,
I am very happy, for the first time I get a fix with my Ublox MAX8 installed on a Crazyflie.
The installation:
P_20171218_151250_r.jpg
a little bit rough, but it works. The energy was obtained with USB connection.
The fix was obtained rather quickly, 1 minute max.
Now, the result, obtained according to the console tab:
------
$GNGSA,A,3,05,07,30,,,,,,,,,,8.17,2.49,7.78*14
$GNGSA,A,3,73,,,,,,,,,,,,8.17,2.49,7.78*11
$GPGSV,2,1,06,05,53,302,20,07,63,071,28,13,22,265,,16,03,022,*75
$GPGSV,2,2,06,20,02,312,,30,71,157,29*72
$GLGSV,2,1,07,70,56,088,20,71,57,330,24,73,49,162,25,74,03,190,*66
$GLGSV,2,2,07,79,03,023,,86,13,260,,87,18,317,*55
------
That means that there are 13 satellites in view, 6 GPS and 7 Glonass. Accuracy is not very good with a PDOP of 8.17. 4 satellites are active, these conclusions according to technical note "u-blox8-M8_ReceiverDescrProtSpec_(UBX-13003221)_Public".
I have to do some work on GPSTab because it did not get the fixing.
Regards
Jean-Claude
Last edited by Mitteau on Sat Dec 30, 2017 9:23 am, edited 1 time in total.
tobias
Bitcraze
Posts: 2339
Joined: Mon Jan 28, 2013 7:17 pm
Location: Sweden

Re: Hurrah! First fix with Ublox

Post by tobias »

Nicely done!

Having the MAX8 close to the CF2 does it effect the possibility to get a fix?

The GPS tab might need some shaping up indeed.
Mitteau
Expert
Posts: 248
Joined: Fri Jan 29, 2016 6:00 am

Re: Hurrah! First fix with Ublox

Post by Mitteau »

Hi
Yes, the GPS,Tab needs a lot of work...
Jean-Claude
Mitteau
Expert
Posts: 248
Joined: Fri Jan 29, 2016 6:00 am

Re: Hurrah! First fix with Ublox

Post by Mitteau »

Hi
I made a new post on my first conclusions on the use of Ubox GPS-Glonass receiver.
The fix is obtained with receiver place at 2-3 cm from the board. But if I put the receiver side by side with cf board, the fix seems to disappear.
Jean-Claude
tobias
Bitcraze
Posts: 2339
Joined: Mon Jan 28, 2013 7:17 pm
Location: Sweden

Re: Hurrah! First fix with Ublox

Post by tobias »

If I recall correctly we tried with a similar GPS breakout board and also experienced problems as soon as we come close to the CF2.
Mitteau
Expert
Posts: 248
Joined: Fri Jan 29, 2016 6:00 am

Re: Hurrah! First fix with Ublox

Post by Mitteau »

The main problem is the long delay to get a first fix (yesterday nearly half an hour). We should try to implement memorization of ephemerides. I am investigating this question.
Mitteau
Expert
Posts: 248
Joined: Fri Jan 29, 2016 6:00 am

Re: Hurrah! First fix with Ublox

Post by Mitteau »

The main problem is the long delay to get a first fix (yesterday nearly half an hour). We should try to implement memorization of ephemerides. I am investigating this question.
tobias
Bitcraze
Posts: 2339
Joined: Mon Jan 28, 2013 7:17 pm
Location: Sweden

Re: [SOLVED]Hurrah! First fix with Ublox

Post by tobias »

This ublox module will probably have much better reception when put close to the CF2. Maybe someone has made a breakout board for it that could be tested on the CF2. Just a thought.
Post Reply