Search found 659 matches
- Mon May 07, 2018 11:15 am
- Forum: Developer Discussions
- Topic: [LEAP MOTION + CRAZYFLIE]
- Replies: 10
- Views: 5551
Re: [LEAP MOTION + CRAZYFLIE]
What approach are you trying, building your own Python 3 bindings? I've never tried it so unfortunately I don't think I be very useful here. But I would recommend separating the problems. Make a Python 3 script that uses the bindings outside the client and make sure everything works. Then integrate ...
- Mon Apr 30, 2018 9:22 am
- Forum: Developer Discussions
- Topic: [LEAP MOTION + CRAZYFLIE]
- Replies: 10
- Views: 5551
Re: [LEAP MOTION + CRAZYFLIE]
Hey man, I tried the older version of the crazyflie client using this link . I believe the leap motion does fine however, I can't seem to connect the crazyradio pa to the crazyflie. I already did all the zadig drivers thing. However it does not do any good. What could be the solution for this one? ...
- Mon Apr 30, 2018 9:16 am
- Forum: Support
- Topic: Cannot connect with Crazyflie
- Replies: 22
- Views: 15790
- Wed Jan 24, 2018 9:27 am
- Forum: Developer Discussions
- Topic: [LEAP MOTION + CRAZYFLIE]
- Replies: 10
- Views: 5551
Re: [LEAP MOTION + CRAZYFLIE]
Hi, When the Crazyflie Python Client was moved from Python 2.7 to Python 3 the Leap Motion support was dropped since there's no bindings for Python 3. I checked the website quickly and I can still only find bindings for Python 2.7. This means that you cannot run the library from within the client. T...
- Mon Dec 18, 2017 12:18 pm
- Forum: Developer discussions
- Topic: ZMQ Question
- Replies: 4
- Views: 3506
- Thu Dec 14, 2017 9:10 am
- Forum: Developer discussions
- Topic: ZMQ Question
- Replies: 4
- Views: 3506
Re: ZMQ Question
It seems as if the ZMQ input us still disabled. Could you try going though the following steps? Start the cfclient and select Settings -> Open config folder Look in the config folder and find config.json . Close the client first then edit the config.json file to enable ZMQ input: "enable_zmq_in...
- Tue Nov 28, 2017 10:01 am
- Forum: Support
- Topic: [SOLVED] Making the Buzzer Deck play sounds from a Python script
- Replies: 1
- Views: 1695
Re: Making the Buzzer Deck play sounds from a Python script
Hi, It's possible to set tones or melodies from the Python API using parameters, but this will not work well for playing longer sequences because the timing will probably be off. If you want a new melody the best is to modify the firmware. The sound_cf2.c contains everything you need. Just clone the...
- Fri Nov 10, 2017 10:09 am
- Forum: Support
- Topic: [SOLVED] Electrical contact failure
- Replies: 9
- Views: 4297
Re: [CAN'T BE SOLVED] Electrical contact failure
Sorry to hear that you weren't able to fix it. If you have Flux try adding a bit of that while melting the soldering, this will make the solder creep better.
- Fri Nov 10, 2017 10:04 am
- Forum: Support
- Topic: Cannot turn crazyflie 2.0 off
- Replies: 2
- Views: 2505
Re: Cannot turn crazyflie 2.0 off
Hi, It sounds like you have entered bootloader mode. You should be able to turn on/off the Crazyflie 2.0 by pressing the power button with a click, if you hold it down for 3 seconds or more while powering it on you will enter bootloader mode and the M2 and M3 LEDs will blink. If you're still not abl...
- Mon Nov 06, 2017 2:05 pm
- Forum: Bitcraze
- Topic: crazyflie programming where>start?
- Replies: 4
- Views: 3448
Re: crazyflie programming where>start?
Thanks for the feedback, I agree that there's improvements to be made. i got the python client which runs great took ages to get setup but finally got the figure of 8 thanks. Did you run the example from the Bitcraze VM or did you install the library nativ? i did follow and complete the getting star...