Search found 2338 matches

by tobias
Wed May 25, 2022 7:00 am
Forum: Support
Topic: crazyradio PA connect issue
Replies: 8
Views: 77483

Re: crazyradio PA connect issue

Adding to that, I was referring to the cfclient console. If you don't get any output when connecting with radio you can try with USB. If you are using the VM don't forget to hand over the Crazyflie USB device to the VM.
by tobias
Tue May 24, 2022 8:03 am
Forum: Support
Topic: Flowdeck is not working properly
Replies: 1
Views: 18314

Re: Flowdeck is not working properly

It looks like the flow deck is not identified correctly. Possibly the 1-wire memory is corrupt or empty. Please try the following (assuming crazyflie-lib-python has been installed). Download the write-ow-flow2.py python script Connect only the flow v2 deck to the CF2.1, no other decks Power on the C...
by tobias
Tue May 24, 2022 7:49 am
Forum: Support
Topic: crazyradio PA connect issue
Replies: 8
Views: 77483

Re: crazyradio PA connect issue

There is a chance it is hardware problem with the radio. It would be good if you could post the cfclient console output here. You can get this by connecting with the USB cable as well if the radio can't connect.
by tobias
Fri May 20, 2022 7:51 am
Forum: Quadcopters
Topic: Bolt Motor/ESC/Battery choose
Replies: 2
Views: 42250

Re: Bolt Motor/ESC/Battery choose

I'll do my best to answer your questions Have a question about the battery. In the video, there is a setup that uses a Li-Ion battery. But I don't want to use that in my project. If I switch to a 500mAh 1S LiPo battery, which is 1/5 of the capacity of the one in the video. Will I also only get 1/5 o...
by tobias
Tue May 10, 2022 7:58 am
Forum: General discussions
Topic: Big Quad Deck and Flow Deck
Replies: 2
Views: 19106

Re: Big Quad Deck and Flow Deck

Hi! When you write measure precisely, what precision do you need. The precision is somewhat undefined from the Flow deck as it very much depends on how well it is able to track the surface. The flow deck can be used with the big-quad deck with a patch. You can read about it in the development tab un...
by tobias
Tue May 03, 2022 9:06 am
Forum: Developer Discussions
Topic: Hbridge deck design for bidirectional motor control
Replies: 2
Views: 19219

Re: Hbridge deck design for bidirectional motor control

It is hard to tell the best way forward and if you want to use the flow deck, LPS etc already hogging the BigQuad PWM outputs is a problem. A couple of options I can think of Use a separate MCU on the deck to drive the H-bridges and motors. Could use I2C as interface to not hog any pins but this sol...
by tobias
Wed Apr 27, 2022 2:48 pm
Forum: Bitcraze
Topic: Crazyflie 2.1 Hardware Consistency Issue
Replies: 8
Views: 76551

Re: Crazyflie 2.1 Hardware Consistency Issue

If you have the possibility change the full power path between the new and old. That is battery, motors, props. Then check the hover thrust again. This would tell us if the any of these components are the issue.
by tobias
Mon Apr 25, 2022 12:34 pm
Forum: Quadcopters
Topic: Crazyflie Bolt parts are damaged when trying to fly a DIY drone.
Replies: 3
Views: 25749

Re: Crazyflie Bolt parts are damaged when trying to fly a DIY drone.

Wire the battery to the PDB but also in parallel to the Bolt so that it can measure the voltage and power it. Wire the ESC signals from the bolt (middle wire) to the ESC and power the ESCs from the PDB. Could it be that you held the drone up-side-down? That would trigger tumble detection and shut of...
by tobias
Mon Apr 25, 2022 12:28 pm
Forum: Bitcraze
Topic: Crazyflie 2.1 Hardware Consistency Issue
Replies: 8
Views: 76551

Re: Crazyflie 2.1 Hardware Consistency Issue

The propellers look balanced enough. The WARNING is due to the propeller test is hogging the loop and not an error. Are you running the same firmware as you are not getting the warning on the old crazyflie?
by tobias
Wed Apr 20, 2022 7:20 am
Forum: Quadcopters
Topic: Crazyflie Bolt parts are damaged when trying to fly a DIY drone.
Replies: 3
Views: 25749

Re: Crazyflie Bolt parts are damaged when trying to fly a DIY drone.

Yes, this is most likely caused by over current. I suggest you to use a PDB and not run the power though the Bolt on your setup.

With a hot air station it is possible to replace the mosfet. If you use a PDB you don't really need the mosfet, only the motor signal wire, the middle one.