Hi
Because the power switch broke I am using a wire to turn Crazyflie on and off, so I think that the delay is being cause by me not turning power on properly, it takes me a few tries until I see the red led lit then off then back on and flickering I know then that it has connected.
Regards
Rodrigo
Search found 49 matches
- Thu May 12, 2022 12:36 am
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
- Wed May 11, 2022 9:02 am
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
Re: Cannot connect crazyflie
Hi Yes the led blinks fast about 5 times per second then it briefly stops and blinks again and so on. Yes I am using the aideck-gap8-examples/examples/other/wifi-img-streamer. Yes I am able to connect and run opencv-viewer.py and the window opens and I can see the images, this part works fine. What ...
- Wed May 11, 2022 5:39 am
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
Re: Cannot connect crazyflie
Hello Marcus Thank you for your reply, maybe I wasn’t clear in my last reply, I do connect to the WiFi streaming example, the issue is that I find it takes too long to establish a connection, and I have noticed how the red led on the right hand side of camera flashes very bright and fast when it con...
- Mon May 09, 2022 11:59 am
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
Re: Cannot connect crazyflie
Hello I did what you suggested and I am getting same results, I have to turn wifi off and on, still not connecting as it did before, I don’t know if it is my router or the aideck. What else can you suggest? I tried to flash the esp firmware with cfloader but I get this error: could not save cache, n...
- Wed Apr 27, 2022 10:35 pm
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
Re: Cannot connect crazyflie
hi marcus here is the output from consle SYS: Crazyflie 2.0 is up and running! SYS: Build 38:2a282b575c25 (2022.03 +38) CLEAN SYS: I am 0x313139313535511300360046 and I have 1024KB of flash! CFGBLK: v1, verification [OK] DECK_CORE: 1 deck(s) found DECK_CORE: Calling INIT on driver bcAI for deck 0 AI...
- Wed Apr 27, 2022 6:40 am
- Forum: AI-deck
- Topic: Cannot connect crazyflie
- Replies: 11
- Views: 52905
Cannot connect crazyflie
Hi I am having a problem after running tb make menuconfig I set ssid and password save it and reflashed the Crazyflie, but the wifi streaming example does not appear on my wifi, so I cannot connect. I am using the latest information and have done all the required steps. Could you let me know what th...
- Mon Apr 25, 2022 12:42 am
- Forum: AI-deck
- Topic: aideck bootloader
- Replies: 26
- Views: 73371
Re: aideck bootloader
Hi Marcus
I fixed the error, had to run docker pull bitcraze/aideck and is now good.
Thank you
Rodrigo
I fixed the error, had to run docker pull bitcraze/aideck and is now good.
Thank you
Rodrigo
- Fri Apr 22, 2022 4:49 am
- Forum: AI-deck
- Topic: aideck bootloader
- Replies: 26
- Views: 73371
Re: aideck bootloader
Hello Marcus I followed the latest aideck examples folder and have tried to run the steps and find that when I try to run the docker script to make the image I get the following error: Docker error response from daemon: failed to create shim : OCI runtime create failed: container_linux.go:380 starti...
- Wed Apr 13, 2022 2:04 am
- Forum: AI-deck
- Topic: aideck bootloader
- Replies: 26
- Views: 73371
Re: aideck bootloader
Hi
Now we can proceed to the bootloader issue. Could you provide me with the instructions.
Thank you
Rodrigo
Now we can proceed to the bootloader issue. Could you provide me with the instructions.
Thank you
Rodrigo
- Mon Apr 11, 2022 5:59 am
- Forum: AI-deck
- Topic: aideck bootloader
- Replies: 26
- Views: 73371
Re: aideck bootloader
Hello Marcus I found the problem and fixed it!!!! It was my fault, as I was trying to flash the GAP8 with the docker code instead of the Nina module, so I did that and now is working!!!!! One thing is that I am getting two images at once, and cannot close windows, is there a command for closing the ...