Search found 27 matches

by tintin
Thu Nov 19, 2020 6:29 pm
Forum: Lighthouse positioning system
Topic: ESTKALMAN: State out of bounds, resetting
Replies: 8
Views: 341

Re: ESTKALMAN: State out of bounds, resetting

O.K., thanks for confirming the observed effect and for pointing towards the app layer option. I might try that.
by tintin
Thu Nov 19, 2020 2:14 pm
Forum: Lighthouse positioning system
Topic: ESTKALMAN: State out of bounds, resetting
Replies: 8
Views: 341

Re: ESTKALMAN: State out of bounds, resetting

Hi,
thanks for the reply. Please let me know if you need more info from my setup to assist your efforts.
Regards
by tintin
Thu Nov 19, 2020 9:55 am
Forum: Lighthouse positioning system
Topic: ESTKALMAN: State out of bounds, resetting
Replies: 8
Views: 341

Re: ESTKALMAN: State out of bounds, resetting

Hi, I have the same "position estimate divergence" problem. I'm using two V1 base stations and followed the LH setup instructions, including pasting the results of the get_bs_geometry.py script into the lighhouse_core.c source file, building and flashing. The CF seems to boot without errors and even...
by tintin
Wed Nov 18, 2020 4:21 pm
Forum: Support
Topic: Thrust commands not accepted when using FrSky TX as controller
Replies: 2
Views: 204

Re: Thrust commands not accepted when using FrSky TX as controller

Hi Arnaud, I've just tried setting the "min thrust" parameter in the cfclient to zero % and this indeed did the trick! I'd already adjusted the thrust axis setup in the FrSky TX SW to cover the full range between 0% and 100% so it was obviously just the lower limit in the cfclient. Thank you so much...
by tintin
Tue Nov 17, 2020 12:49 pm
Forum: Support
Topic: Thrust commands not accepted when using FrSky TX as controller
Replies: 2
Views: 204

Thrust commands not accepted when using FrSky TX as controller

Hi, I'm currently trying to control the CF2.1 (via the cfclient, current version) with a FrSky RC transmitter and the corresponding FrSky USB Sim dongle. The TX/dongle is visible in the OS as a joystick. I'm able to "see" and configure this input device in the cfclient menu and I've created an assoc...
by tintin
Wed Oct 14, 2020 11:08 am
Forum: Support
Topic: cfclient start fails with segmentation fault under Linux
Replies: 6
Views: 736

Re: cfclient start fails with segmentation fault under Linux

Hi,
I've just removed and then reinstalled the cfclient after today's bugfixes: now everything seems to work again and I didn't see any unexpected error messages in the terminal output.
Thanks for the quick support effort!

Regards
Tintin
by tintin
Tue Oct 13, 2020 1:57 pm
Forum: Support
Topic: cfclient start fails with segmentation fault under Linux
Replies: 6
Views: 736

Re: cfclient start fails with segmentation fault under Linux

Hi,
in my desperation I also tried to install the cfclient via snap as per the published instructions. The installation worked but the client won't start. No error messages whatsoever.
Hope you come up with a fix soon, since I'm completely grounded.
Regards
Tintin
by tintin
Tue Oct 13, 2020 6:38 am
Forum: Support
Topic: cfclient start fails with segmentation fault under Linux
Replies: 6
Views: 736

Re: cfclient start fails with segmentation fault under Linux

Hi,
the cfclient on the official bitcraze VM is broken too after a pull, btw.
Regards
Tintin
by tintin
Mon Oct 12, 2020 6:01 pm
Forum: Support
Topic: cfclient start fails with segmentation fault under Linux
Replies: 6
Views: 736

Re: cfclient start fails with segmentation fault under Linux

Hi, I followed your instructions but I still get the segmentation fault: INFO:cfclient.gui:Disabling STL printouts INFO:cfclient.utils.input.inputreaders:Input readers: ['linuxjsdev', 'pysdl2'] INFO:cfclient.utils.input.inputreaders:Successfully initialized [linuxjsdev] INFO:cfclient.utils.input.inp...
by tintin
Sat Oct 10, 2020 2:25 pm
Forum: Support
Topic: cfclient start fails with segmentation fault under Linux
Replies: 6
Views: 736

Re: cfclient start fails with segmentation fault under Linux

The problem also occurs on another linux machine: python3 ~/Development/bitcraze/crazyflie-clients-python/bin/cfclient INFO:cfclient.gui:Disabling STL printouts INFO:cfclient.utils.input.inputreaders:Input readers: ['linuxjsdev', 'pysdl2'] INFO:cfclient.utils.input.inputreaders:Successfully initiali...