Search found 22 matches

by tdubick
Wed Apr 10, 2019 3:01 am
Forum: Support
Topic: Thanks for all the help - we got 'em swarming
Replies: 2
Views: 1880

Thanks for all the help - we got 'em swarming

Folks,

Everyone thanks for the help over the past few days/weeks. We have the drones swarming. My high school and middle school programmers are excited.

Thanks Again,
Tom
by tdubick
Thu Apr 04, 2019 3:53 pm
Forum: Support
Topic: Importance of a fully charged battery
Replies: 6
Views: 5328

Re: Importance of a fully charged battery

I was able to assign locations to each node. I just needed to wait about 15 second from when I wrote to the node and it changed red to when it went green.


Unfortunately, all the drones stilling flat show on the flight panel to be spinning. The blue dot is jumping all over LPS.

Thanks,
Tom
by tdubick
Thu Apr 04, 2019 1:56 pm
Forum: Loco Positioning System
Topic: LOC Node Setup
Replies: 5
Views: 3167

Re: LOC Node Setup

Yes, I was able to assign locations last night. I think it would be helpful in the isnstructions that it might take 15 seconds before you will see the color go from red (you just wrote to position) to green system is updated. The new issue is my drones are sitting flat in the center of the LPS but t...
by tdubick
Wed Apr 03, 2019 10:38 am
Forum: Loco Positioning System
Topic: LOC Node Setup
Replies: 5
Views: 3167

Re: LOC Node Setup

Thank you for your reply.

I added each anchor and then I wrote location to each. Anchors did turn green but their location information was 0,0,0. Thanks for any help

LOCOSS6.PNG
by tdubick
Tue Apr 02, 2019 10:27 pm
Forum: Loco Positioning System
Topic: LOC Node Setup
Replies: 5
Views: 3167

LOC Node Setup

Folks, I feel my students and I are getting close. We were able to install the current firmware into the anchors and we assigned each anchor. We set up the anchors and in 1.8 meters x 1.8 meters x 2.0 meters. We are using a USB cable to power each anchor. We start up a drone using a PC Client. When ...
by tdubick
Tue Apr 02, 2019 12:27 pm
Forum: Support
Topic: LOC Nide drivers
Replies: 8
Views: 6377

Re: LOC Nide drivers

Ok,

I just tried a different computer and I was able to immediately able to use LPS to assign the nodes. The nodes are now appearing on the pc client. I hope to do more testing between classes and with my students.

Tom
by tdubick
Mon Apr 01, 2019 6:07 pm
Forum: Support
Topic: LOC Nide drivers
Replies: 8
Views: 6377

Re: LOC Nide drivers

Here is a screen shot of the device manager and LPS tool. I have already updated the firmware.
LPSScreenshot1.PNG
by tdubick
Mon Apr 01, 2019 5:35 pm
Forum: Support
Topic: Importance of a fully charged battery
Replies: 6
Views: 5328

Re: Importance of a fully charged battery

Hi,

I use the win32 driver and I was able to get pc client to work in terms controlling the drone. I am still trying to get the LOC nodes to update. I was able to install firmware once I used win32 instead of WinUSB. I have not been able to assign LOC nodes on my PC

Tom
by tdubick
Mon Apr 01, 2019 5:32 pm
Forum: Support
Topic: LOC Nide drivers
Replies: 8
Views: 6377

Re: LOC Nide drivers

Hi,

I am sorry I don't understand. I was able to upload the firmware. I replace the driver with USBWin and it still did not work.
I tried the other drives with no luck.

Tom
by tdubick
Mon Apr 01, 2019 2:47 pm
Forum: Support
Topic: LOC Nide drivers
Replies: 8
Views: 6377

Re: LOC Nide drivers

Let me begin by saying thanks for the help. Good new - I was able to update the firmware once I replaced the WinUSB driver with libusb-win32 driver. The libusbK did not work. I did try that first. Bad news - I was unable to configure the Loco Positioning node after udpating the firmware. I made sure...