Thanks for the response tobias!
I'll fill up the form.
Search found 13 matches
- Tue Apr 18, 2017 5:55 pm
- Forum: Support
- Topic: Crazyflie 2 - strange behaviour - ACC/GYRO defect?
- Replies: 6
- Views: 3861
- Mon Apr 17, 2017 3:18 pm
- Forum: Support
- Topic: Crazyflie 2 - strange behaviour - ACC/GYRO defect?
- Replies: 6
- Views: 3861
Re: Crazyflie 2 - strange behaviour - ACC/GYRO defect?
Were you able to figure out the issue?
I'm facing a similar problem.
My quad didnt crash though. It is behaving weird all of a sudden.
I'm facing a similar problem.
My quad didnt crash though. It is behaving weird all of a sudden.
- Mon Apr 17, 2017 3:16 pm
- Forum: Support
- Topic: CrazyFlie acting crazy [SOLVED]
- Replies: 6
- Views: 3926
Re: CrazyFlie acting crazy
Were you able to figure out the issue?
I'm facing a similar problem.
the quad stays disoriented. One of the motors doesnt even spin until I turn it 90 degrees.
I'm facing a similar problem.
the quad stays disoriented. One of the motors doesnt even spin until I turn it 90 degrees.
- Sat Apr 15, 2017 3:26 pm
- Forum: Support
- Topic: CrazyFlie 2.0 doesn't boot or charge
- Replies: 13
- Views: 9373
Re: CrazyFlie 2.0 doesn't boot or charge
Hi Tobias,
That worked. I kept the on/off button pressed while connecting the power source.
It started in bootloader mode and I updated it using ios client.
Thanks for your advice!
It is working but there seems to be some problem with the gyro now.
It stays disoriented and is not calibrating.
That worked. I kept the on/off button pressed while connecting the power source.
It started in bootloader mode and I updated it using ios client.
Thanks for your advice!
It is working but there seems to be some problem with the gyro now.
It stays disoriented and is not calibrating.
- Mon Apr 10, 2017 5:39 pm
- Forum: Support
- Topic: CrazyFlie 2.0 doesn't boot or charge
- Replies: 13
- Views: 9373
Re: CrazyFlie 2.0 doesn't boot or charge
I'm in a similar situation. I was updating the Crazyflie 2.0 from IOS app. It failed, I turned off the quad and turned it back on. Only M2 is lit solid. It is not getting into bootloader mode no matter how long I press the on/off switch. On/off switch doesn't have any effect on the status on M2. I m...
- Sun Mar 29, 2015 2:55 am
- Forum: General discussions
- Topic: The easiest and best Controller
- Replies: 10
- Views: 8428
Re: The easiest and best Controller
i got a PS3 compatible and it works great out of the box!
- Sun Mar 29, 2015 2:28 am
- Forum: Support
- Topic: Crazyflie 2.0 I2C FAILURE
- Replies: 32
- Views: 18531
Re: Crazyflie 2.0 I2C FAILURE
I received a replacement board for my Crazyflie ten days back and I'm back on track.
Thanks a lot Tobias!
Thanks a lot Tobias!
- Tue Mar 10, 2015 5:46 am
- Forum: Support
- Topic: Crazyflie 2.0 I2C FAILURE
- Replies: 32
- Views: 18531
Re: Crazyflie 2.0 I2C FAILURE
tobias wrote:Both things sounds like the sensor soldering issue. I've sent you both a PM.
Thanks a lot Tobias!
I've replied back to your PM.
The message is stuck in my outbox!
- Mon Mar 09, 2015 4:09 am
- Forum: Support
- Topic: Crazyflie 2.0 I2C FAILURE
- Replies: 32
- Views: 18531
Re: Crazyflie 2.0 I2C FAILURE
Using the schematics and placement diagram I was able to locate the component MPU9250 (labeled U9 on the placement diagram). It's a small square chip, located on the top of the board, just inside the expansion board pin strip on the left-hand side - right next to a symbol that looks like it's suppo...
- Sat Mar 07, 2015 9:52 am
- Forum: Support
- Topic: roll pitch yaw calibration
- Replies: 13
- Views: 11175
Re: roll pitch yaw calibration
This looks similar to a few crazy values people have been posting that end up being IMU issues. Have you crashed much since you got it? Also, is there any drift other than yaw drift? I also have to wonder if the IMU is getting a bit hot and causing the errors and loss of alignment. Perhaps they nee...