Search found 43 matches
- Wed Feb 22, 2017 12:52 pm
- Forum: Developer Discussions
- Topic: Qi wireless charging using another coil
- Replies: 3
- Views: 2434
Re: Qi wireless charging using another coil
Have you checked the datasheet of the wireless receiver ship? Of course. I try to make it work without luck. Does part number of the coil that used in Crazyflie 2.0 Qi wireless charger is known? I am searching for Coil part number that will work with Crazyflie 2.0 Qi wireless charger schematic. Can...
- Thu Feb 02, 2017 5:52 pm
- Forum: Developer Discussions
- Topic: Qi wireless charging using another coil
- Replies: 3
- Views: 2434
Qi wireless charging using another coil
Hello. I try to design qi wireless charger using smaller coil. Here is coil that I use: http://www.digikey.com/product-detail/en/abracon-llc/AWCCA-12R12H11-C01-B/535-13306-ND/5801533 But, unfortunately LED not lights up when I desolder default coil and use that new coil. Do I need to change capacita...
- Sat Dec 05, 2015 11:51 pm
- Forum: Developer Discussions
- Topic: Roll pitch angles above 900 degree
- Replies: 1
- Views: 1614
Roll pitch angles above 900 degree
Hello!
When I turn quadrocopter at an angle greater than 90 degrees, then I start getting wrong values of current angles. What is the reason? Is there a way to fix this?
When I turn quadrocopter at an angle greater than 90 degrees, then I start getting wrong values of current angles. What is the reason? Is there a way to fix this?
- Mon Sep 07, 2015 7:36 am
- Forum: Developer Discussions
- Topic: mpu-9250 on the bottom layer
- Replies: 1
- Views: 1497
mpu-9250 on the bottom layer
Hi! I am developing my own quadrotor, so I need advice about placing mpu-9250. There is altimeter and MCU are placed on the bottom layer of crazyflie-2.0. Is it possible to place mpu-9250 also on the bottom layer of my own pcb? I need to do that because there is gps antenna will be placed on the top...
- Wed Jun 10, 2015 12:58 pm
- Forum: Developer Discussions
- Topic: PCB Project File
- Replies: 4
- Views: 3000
Re: PCB Project File
Still not available?
- Tue Apr 14, 2015 8:54 am
- Forum: Developer Discussions
- Topic: Debug crazyflie 2.0 JTAG
- Replies: 1
- Views: 2170
Debug crazyflie 2.0 JTAG
Hello. I need to debug crazyflie 2.0 via JTAG. For this i connect JLink to debug adapter kit ( in 20 pin jack ) and connect debug adapter kit to crazyflie 2.0 via 6 pin jack. JLink can't detect quadcopter's chip. What I need to solder to connect quadcopter's chip with JLink via debug adapter kit? Th...
- Sun Mar 29, 2015 9:35 am
- Forum: Bitcraze
- Topic: Crazyflie 2.0 Model/STL files
- Replies: 17
- Views: 15916
Re: Crazyflie 2.0 Model/STL files
Hello! Is there crazyflie 2.0 motor support 3D model available to little bit modify it and manufacture it on 3D printer? I need distance sensor to be mounted on crazyflie 2.0.
- Sun Mar 29, 2015 9:22 am
- Forum: Developer Discussions
- Topic: Power crazyflie 2.0 from 7.4 volt
- Replies: 3
- Views: 2671
Re: Power crazyflie 2.0 from 7.4 volt
Thank you)akbarhash wrote: Any of these can power the crazyflie.
- Sat Mar 28, 2015 1:48 pm
- Forum: Developer Discussions
- Topic: Power crazyflie 2.0 from 7.4 volt
- Replies: 3
- Views: 2671
Power crazyflie 2.0 from 7.4 volt
Hello! I want to apply on board sensor which requires 6 volt power supply. So, there is any way to power on crazyflie 2.0 from 7.4 Volt. I tried to look for any 7.4 - 3.7 dc converter without luck. Need any advice!
- Sat Mar 28, 2015 1:20 pm
- Forum: Developer Discussions
- Topic: [SOLVED] Selecting an ultrasonic sensor and interface
- Replies: 71
- Views: 6799461
Re: [SOLVED] Selecting an ultrasonic sensor and interface
Yes, it work without any trobles.tobias wrote: Have you already tried this?
As will be logically completed firmware ( also 2 sensor ) - i will put in on github.tobias wrote:Will be exiting to follow what you are up to!