Search found 13 matches
- Fri Jan 02, 2015 8:03 am
- Forum: Support
- Topic: M1 stopped flashing [SOLVED]
- Replies: 5
- Views: 3418
Re: M1 stopped flashing
Since everything is working fine and I get a nice new feature I think I am fine with the new behavior.
- Wed Dec 31, 2014 5:22 pm
- Forum: Support
- Topic: M1 stopped flashing [SOLVED]
- Replies: 5
- Views: 3418
Re: M1 stopped flashing
Thanks for the answer,
this makes sense but in the beginning the LED was only flashing, the permanent red behavior started yesterday and i´ve not changed the firmware, kinda funny.
this makes sense but in the beginning the LED was only flashing, the permanent red behavior started yesterday and i´ve not changed the firmware, kinda funny.
- Wed Dec 31, 2014 12:34 pm
- Forum: Support
- Topic: M1 stopped flashing [SOLVED]
- Replies: 5
- Views: 3418
M1 stopped flashing [SOLVED]
Yesterday I crashed the Crazyflie 2 and one of the motor connectors was bend a little. I pushed it back into position and everything is working fine. Except the LED M1, usually it was flashing in red (the heartbeat) but now it changes after a short period of time in flight into a permanent red. What...
- Sun Dec 28, 2014 8:09 am
- Forum: General discussions
- Topic: Trim values step [SOLVED]
- Replies: 3
- Views: 2493
Re: Trim values step
Thanks,
this worked quit nicely, I´ve looked in all the .json files except for this one.
this worked quit nicely, I´ve looked in all the .json files except for this one.
- Sat Dec 27, 2014 2:14 pm
- Forum: General discussions
- Topic: Trim values step [SOLVED]
- Replies: 3
- Views: 2493
Trim values step [SOLVED]
is it possible to change the increasing/deceasing amount of the trim values set by the controller ? At the moment each press on the controller buttons changes the trim values for +/- 1 but i wold like to set this value much lower e.g. 0.1-0.5 to get a better hoover behavior. It (CF2) hoovers quite g...
- Wed Dec 24, 2014 5:29 pm
- Forum: Support
- Topic: [SOLVED]: First flight: Crazyflie goes wild, now no telemetr
- Replies: 8
- Views: 5082
Re: First flight: Crazyflie goes wild, now no telemetry or f
i´ve had a similar event, but not as dramatic as yours.
The flie was hovering over the ground (indoor) and both front motors went up to 100% without any reason.
It crashed into the furniture but nothing was broken and it is still working.
The flie was hovering over the ground (indoor) and both front motors went up to 100% without any reason.
It crashed into the furniture but nothing was broken and it is still working.
- Mon Dec 22, 2014 8:57 am
- Forum: Support
- Topic: [SOLVED] Segmentation fault at exit of gui
- Replies: 27
- Views: 32413
Re: Segmentation fault at exit of gui
for me the newest version dosen´t work at all: INFO:cfclient.cfclient:Disabling STL printouts INFO:cfclient.utils.config:Dist config read from /usr/cfclient/configs/config.json INFO:cfclient.utils.config:Config file read from [/root/.local/cfclient/config.json] ===== 2014.12.22 09:12:01 ===== Traceb...
- Thu Dec 18, 2014 3:34 pm
- Forum: Support
- Topic: [SOLVED] Segmentation fault at exit of gui
- Replies: 27
- Views: 32413
Re: Segmentation fault at exit of gui
i´ve tried the workaround and it´s working.
- Wed Dec 17, 2014 8:19 am
- Forum: Support
- Topic: [SOLVED] Segmentation fault at exit of gui
- Replies: 27
- Views: 32413
Re: Segmentation fault at exit of gui
I have the same issue on an opensuse 13.1.
Exactly like you said, by starting "configure device mapping" and by closing the gui i get a segmentation fault.
A (bad) workaround for me is to change the mappings and then start "configure device mapping" this works.
Exactly like you said, by starting "configure device mapping" and by closing the gui i get a segmentation fault.
A (bad) workaround for me is to change the mappings and then start "configure device mapping" this works.
- Sat Nov 15, 2014 9:24 am
- Forum: Support
- Topic: PS3 OpenSuse Mapping [SOLVED]
- Replies: 6
- Views: 3767
Re: PS3 OpenSuse Mapping
This script is relay nice. I had to change the length of the array but now it is working. And the funny thing is that the axis won´t be recognized. All buttons and axis are working but i can´t get a signal for the left stick x-axis. So it looks like something more deep like a driver problem. -------...